Fire extinguisher mounting


Thanks Pete, Bony and Black Ice for the tips and fast response!


Much appreciated!

Got the bolts Pete! Thanks a bunch!
 
Last edited:
Thanks Pete, You're Welcome Bony

Just received the bolts Pete! Thanks. Good idea.

Bony - anything 4 U man!!! :)

Ed
 
Just received my bolts too. Thanks so much for pointing out the problem and providing the solution. I owe you...
 
:thumbsup I got my bolts yesterday, thanks!:thumbsup
:cheers
 
5 More sets available . . . .

PM me an address, otherwise I'll send them up to Rich and Denis aka The GT Guy.(s)
 
mounting extinguisher

I mounter it below the speaker between the seats so that you could get to it easilt.
 
extinguisher mounted between the seats

Ernest - I tried mounting it between the seats but my wife wouldn't let me.

Ed
 
BlackICE said:
T50

I cut a T50 down as short as possible and put it back into its 3/8" drive rachet holder. Then connected it to a long wobble extension. The extension compresses the cushion, but it has a smooth finish and didn't cause any damage.

Also use hand tools, it will be a lot safer, not the Makita.
Click to expand...

Did you use a 1, 2, 5, or 8 inch wobble extension?

The Makita in the picture is just a light, so that would make for a unusually tough install. :wink
 
The bolts arrived yesterday. Thanks so much Pete !
BTW the card is very cool. What a great idea.
 
I used an extension that was long enough so that the rachet handle as above the seat cushion and only the small diameter of the extension was rubbing on the compressed seat cushion.
 
Perfect. Thanks BlackICE. I just ordered my 9 piece wobble extension set up from eBay, so I will be ready to go soon...
 
You also may need tools to cut down a t50 torx bit. I used a Remington carbide hacksaw blade.
 
I was lazy, Evan at Guyett Performance installed mine without issues. Again thanks Ed for designing the slick bracket.
 
Hmmm. Why does the T50 torx bit need to be cut down? How does that help?
 
SYCO GT said:
Hmmm. Why does the T50 torx bit need to be cut down? How does that help?
Click to expand...
So that the wobble is futher down. Then you can angle the extention sooner for less conpression of the seat cushion.
 
You're welcome Mr Bony

Thanks for always thanking me Bony. You are too nice. Can you make it to Buttonwillow on this coming Saturday June 23 for the NCRC open track? There should be a few other GTs besides mine. It's not too far from you. Or you can meet us for dinner Friday night.

Ed
 
That's it.

The extra bolts & washers have been sent off, there are no more.

Pete S.
 
Got my bolts Pete. Thanks a bunch!

Keith
 
Has anyone relocated the MAC subwoofer behind the passenger seat and mounted the fire extinguisher? In my GT I need the seat pretty far back to accomodate the extinguisher and I wonder if there is sufficient room back there now to do a subwoofer relocation like the one Shadowman designed.
 
Cheers! Thanks Wally (skills), Pete S (parts), and BlackIce (tech advice) for helping me properly mount my bracket. It was tough to get the bolts back in, after removal. I watched as Wally was able to manipulate the seat rails enough to get the bolts into their threads, something I could not do alone. Removal was a piece of cake, but Wally also mentioned, that although the wobble extension is good for removal, it is not so good with installments.

The black extinguisher would not look out of place in a wine cellar. Beautiful finish. In fact, each and every component of the entire kit is well done. Bracket itself is a beauty in its simplicity and purposeful design.

IMG_6851.jpg


IMG_6852.jpg


T50, 3/8 Socket, Wobble Extension, 7mm Allen, Factory Bolts (replaced with Pete's longer bolts and washers)

IMG_6847.jpg


IMG_6848.jpg
 
Last edited:
You must log in or register to reply here.

Top Bottom