Search results

I certainly think it would not be that hard to contact Guinness and place some kind of formal challenge against this "record". Certainly it has been done before with the many records that they have in their books. I'm sure there is a procedure just like at any other record level competition. I...

Well it's unfortunate for an incident like this to be so controversial. You will have the people that you can sell anything to believing it. (Unfortunately thats more than you think) And you will have the rest who actually know better, trying to figure out how someone was able to fool the...

Well, knowing what I know about going fast, the equation doesn't add up. 1500 HP wont get you to 283 mph unless the track faces downhill at a 45 degree angle. Ray's car and Mark's car make over 2000 hp. A stellar launch will only add a little to the top end speed as its all horsepower at that...

The seal is not available from Ford. You can only but the complete assembly. I have a comparable seal that we use in all of our rebuilds. The seal is very unlikely to leak, normally a leak comes through the ID bushing. Thanks John Accufab Inc

Thanks, John. It was good talking to you today. It's been a long time since that Motor Trend shoot. Glad that you guys chose us to participate in your engine program. I am looking forward to stepping it up again the next time they go out. They did a great job and it was nice to be a part of a...

Specifically about the turbo engine, the turbine is spun by the volume and velocity of air forced through the turbine. A lower compression engine just by nature makes less cylinder pressure thus less BANG when it fires. So the turbo is slower to respond and ultimately cannot make as much...

Here's the answer I have for cam balancing specific to this application. The valvetrain in these engines is very sensitive. Far more sensitive than anyone really understands as a practical matter of discussion. Every cam profile I have developed over the years one of the most important...

http://www.youtube.com/watch?v=86uLwXstuWQ Accufab Mustang in Las Vegas last weekend. 52 psi boost John

It pulls 3.4 g's on the starting line. Typically .98 60'. John

Ford used the IW part because it was cheaper not better. Bean counters I guess. I recently saw 2 2011 Mustangs back to back on the dyno break the oil pump gears after installing the "other" balancer. I told the customer not to use this balancer but he insisted anyway. Both engines are locked up...

I was hoping to avoid this subject but... I simply would not use any other balancer than ATI. If you can afford a $160,000 car, you can afford a good balancer. As for drilling the crank and using a roll pin, due to the limited space and the inherent half ass idea of that, I would prefer the...

See this 6.25 @229. http://www.youtube.com/watch?v=pMK7hOEGWSw John

Its kinda funny how there are so many opinions about this subject from so many that have never seen the internals of this engine. I know of a couple failures already and have fixed a couple. Not everyone posts their failures on this or any message board just so you know. Some poeple actually...

I am not in the business of crying wolf unless I see one. Everyone has been advised of the issue. No, there is no easy fix, but I do have one. Don't wait until the balancer flies off because the repair costs will probably be triple due to the damage done. As for Ford, theres a reason that they...

The issue with the crank is simple. It is fine in the application it was designed for. Adding a Whipple is outside of that design parameter. Now, that does not mean to call Whipple and complain either. Its simple physics and some good old common sense. The keyway is very small, the factory bolt...

The 6 spoke wheels are gone as well as the rear bumper, thanks guys John

I have another engine just like Rays. It's his spare I'm building. You are going to need a little more cash than than that that however. I do have plenty of spare engine parts, but only selling that stuff as part of engine builds. The engine building stuff has been very busy lately. John

Well, it's about time to clean out the shop once again. I have the following GT parts for sale 1. 1 set brand new Ford GT 6 spoke wheels, no center caps $1900 2. 1 set brand new Goodyear 235-45-18 stock front tires $600 3. 1 brand new rear Goodyear 315-40-19 stock rear tire $500 4. 1 used BBS...

Having a civilized rivalry is always what's best for raising the bar at any type of competition. I like having a target on my back because it just makes me better. I work best under pressure and I haven't felt any yet. I think the goals that Ray has for his cars are attainable and will be fun...

There sure is a little deception in that Ebay ad don't you think. Either way quitters are always looking for a reason to quit. Winners never quit despite what obvious obstacles are in their path. I guess the reality show got cancelled. There's always Jerry Springer. John