Ford Racing 2005-06 Ford Gt Power Upgrade Package Finally Available @ $999.99!!!!!


MMP Inc.

MMP Inc.

Well-known member
Jan 18, 2006
404
www.MuscleMotors.com 818-341-RACE in Sunny Souther
m-2005-gt.jpg


Fits 2005-06 Ford GT
Approximately 100 hp increase
Kit includes supercharger pulley (sizing not released yet) and Pro-Cal tool with official Ford Racing calibration
Detailed instructions included (coming soon)
E.O. #D-231-26

If anyone needs more information on this or would like to order please let us know!

Jack @ MMP Sales
Muscle Motors Performance, Inc.
[email protected]
http://www.musclemotors.com
(818)888-7778
"Here to Make Racing Fun & Affordable for Everyone!"
 
Last edited:
I have to be the bozo to ask THE question. Does it affect the warranty?
 
According to Ford Racing it does not void your factory warranty as it is an authorized Ford part plus it has an EO Carb Number attached to it!
 
What is the diameter of the pulley? 2.76?
 
And only a thousand bucks. What a deal :ack
 
A thousand bucks is a bargain for a pulley, tune, EO number, etc.
 
nota4re said:
A thousand bucks is a bargain for a pulley, tune, EO number, etc.
Click to expand...

Agree.
 
Since it is a Ford part, can I get a Ford Dealer to install it?
 
What is an EO carb #
Thanks
 
CARB = California Air Research Board - presumably the toughest air pollution standards within the US.

EO = Executive Order

In California, any modification to a motor vehicle that could potentially effect emissions is prohibited unless the modification has been tested and approved by CARB, proving that the mod does not increase pollutants. In these cases, CARB will issue a specific EO authorizing the change. Every other year when each car is tested for emissions, the testing facility must match any mods to the car with specific EO numbers or fail the car.
 
  • Like
Reactions: Fubar
what diameter pulley?
 
Updated post with the information Ford Racing tech's gave us!
 
MMP Inc. said:
Kit includes supercharger pulley (sizing not released yet) and Pro-Cal tool with official Ford Racing calibration

If anyone needs more information on this or would like to order please let us know!
Click to expand...

Two quick questions.

How does the Pro-Cal tool work?

How hard is it to swap the pulley?

Thanks,
Waldo
 
Waldo -

How does the Pro-Cal tool work? It will load the program through your vehicles OBDII port. It is a very simple procedure!

How hard is it to swap the pulley? It isn't the easist job to do however if you somewhat mechanically inclined, have some basic tools and have access to a press anyone can do the install.
 
You must remove the supercharger then pull off it's press fit pulley and press the new pulley on. Removing the Supercharger is strait forward and is easier to do if your remove the clamshell. Changing the pullies require special tools that you can rent from some speed shops. Since you are using the stock belt it can be left in place. It is my understanding is that you can tip the supercharger pointing the pulley downward to remove it and reverse the process to reinstall.

The supercharger has some pumbing and wires connected to it that will have to be removed. I did a Whipple install and the process is much the same, with the exception that I had to change the supercharger belt. However I didn't need to do a pulley swap.

I is best to have 3 people to remove the clamshell and a lot of tape to protect the paint. The other stuff can be done by yourself in most cases.
 
  • Like
Reactions: Fubar
Hmmm

MMP Inc. said:
m-2005-gt.jpg


Fits 2005-06 Ford GT
Approximately 100 hp increase
Kit includes supercharger pulley (sizing not released yet) and Pro-Cal tool with official Ford Racing calibration
Detailed instructions included (coming soon)
E.O. #D-231-26

If anyone needs more information on this or would like to order please let us know!

Jack @ MMP Sales
Muscle Motors Performance, Inc.
[email protected]
http://www.musclemotors.com
(818)888-7778
"Here to Make Racing Fun & Affordable for Everyone!"
Click to expand...

Wow, $10.00 per hp - under warranty. Seems very appealing.
My local Ford dealer (Towne Ford) has a GT-trained tech. Should I trust them to do the install?
BlackIce, any opinion here?
And do you think this is the precursor to them releasing the long-awaited axle bolts?
 
t32b said:
Wow, $10.00 per hp - under warranty. Seems very appealing.
My local Ford dealer (Towne Ford) has a GT-trained tech. Should I trust them to do the install?
BlackIce, any opinion here?
And do you think this is the precursor to them releasing the long-awaited axle bolts?
Click to expand...

I believe Towne Ford could do the install, but check with them about having pulley puller and press. Also I would confirm with them that it wouldn't void the warranty. Note that the install labor cost would raise the $10/hp number. My guess would be another $400 to $600 for the install. If you are considering having this done, you can schedule it at the same time as your new axle bolts.
 
I'm all over the Power Upgrade Package. The biggest unknown is whether I can find someone I trust to install it or resort to installing it myself. I generally like to do my own work, but there is something to be said for having a true professional work on your gal.
 
Jason,
Rich aka THE GT TECH now lives in Kingman. Had dinner with our group. He knows the car inside and out, part of the original build team.
Hope all is well, stay safe and thank everyone for the great job you men and women are doing!
God Bless America,
daniel
 
bony said:
Jason,
Rich aka THE GT TECH now lives in Kingman. Had dinner with our group. He knows the car inside and out, part of the original build team.
Hope all is well, stay safe and thank everyone for the great job you men and women are doing!
God Bless America,
daniel
Click to expand...

Rich is awesome. He did a bunch of work on three Boston area cars last summer. Great guy and knows the cars very, very well.

Rob
 
You must log in or register to reply here.

Top Bottom