you might be a redneck if...
- Thread starter soroush
- Start date
B O N Y
MODERATOR & FGT OWNER
There was a FGT that was posted which was for sale and the previous owner removed the badge. Your gal, your call.
BlackICE
GT Owner
shelbyelite
PERMANENTLY BANNED
- May 10, 2007
- 1
JimF
GT Owner
Badge
Lose the badge for a clean look!
I wish I had thought of that when I had the front end touched up, oh well, next time.:confused
Big Dog
Lose the badge for a clean look!
I wish I had thought of that when I had the front end touched up, oh well, next time.:confused
Big Dog
- Aug 8, 2007
- 5,256
JOETWINT
FORD GT OWNER
Fast Freddy
GPS'D 225 MPH
did you take the front end off that car yourself? i am very impresed with the way that front end comes off. i have a cracked windshield and have to replace mine. this does not look to be much harder than it was to replace the windshield on my ford truck last year.
Last edited:
Superfly
HERITAGE GT OWNER
Black Ovals:
http://planetauto.homestead.com/index.html
http://www.billetbadges.com/products.htm
Or you could do what this guy says: ""Easy steps to changing the background color of Ford emblems - Derek Hartman
I've been picking a lot of things up from the Ranger Forum lately, and this one takes the cake. This is a VERY simple way to change the background color of your Ford Emblem, it doesn't have to be blue! All it takes is some sand paper, paint, and some clear coat. Here are the steps:
Step 1 - You will need to get the actual blue center part of the emblem out of the chrome casing that's around it. To do this, use a hair dryer or heat gun and spend about 5 minutes heating both sides of the emblem. The center part is held on with some apoxy. Once it is heated good, use something flat (such as a knife or small screwdriver) and pry the center part out.
Step 2 - Once you have the center part out, sand the back until all of the left over apoxy and the blue part is off. It will look a clear/white color when you sand all of the blue paint off. I used 150 grit sandpaper to do this because it was the only thing I had around the house. Once all the blue paint is off the back of the center part, wet sand LIGHTLY to smoothen everything out.
Step 3 - Mask off the front of the emblem, and spray the sanded side with a color of your choice (I chose black). Allow to dry THROUGHLY!
Step 4 - When the paint is dry and you remove the tape, you see that the background color is no longer corporate blue, but the color of YOUR choice! If necessary, wet sand the front side of the center piece and spray a few coats of clear coat onto it. I did this because I had a few chips from rocks, etc.
Step 5 - Replace the center piece back into the chrome surround using double sided tape or apoxy. Re-attach the emblem to your Ex, and enjoy!"
No affiliation with these guys. Bony, they're not sponsors, so you may edit this if need be and I'll just PM Soroush.
http://planetauto.homestead.com/index.html
http://www.billetbadges.com/products.htm
Or you could do what this guy says: ""Easy steps to changing the background color of Ford emblems - Derek Hartman
I've been picking a lot of things up from the Ranger Forum lately, and this one takes the cake. This is a VERY simple way to change the background color of your Ford Emblem, it doesn't have to be blue! All it takes is some sand paper, paint, and some clear coat. Here are the steps:
Step 1 - You will need to get the actual blue center part of the emblem out of the chrome casing that's around it. To do this, use a hair dryer or heat gun and spend about 5 minutes heating both sides of the emblem. The center part is held on with some apoxy. Once it is heated good, use something flat (such as a knife or small screwdriver) and pry the center part out.
Step 2 - Once you have the center part out, sand the back until all of the left over apoxy and the blue part is off. It will look a clear/white color when you sand all of the blue paint off. I used 150 grit sandpaper to do this because it was the only thing I had around the house. Once all the blue paint is off the back of the center part, wet sand LIGHTLY to smoothen everything out.
Step 3 - Mask off the front of the emblem, and spray the sanded side with a color of your choice (I chose black). Allow to dry THROUGHLY!
Step 4 - When the paint is dry and you remove the tape, you see that the background color is no longer corporate blue, but the color of YOUR choice! If necessary, wet sand the front side of the center piece and spray a few coats of clear coat onto it. I did this because I had a few chips from rocks, etc.
Step 5 - Replace the center piece back into the chrome surround using double sided tape or apoxy. Re-attach the emblem to your Ex, and enjoy!"
No affiliation with these guys. Bony, they're not sponsors, so you may edit this if need be and I'll just PM Soroush.
fjpikul
GT Owner
- Aug 8, 2007
- 5,256
thank you so much, that exactly what I was looking for, this will save me a lot of headache, I love this forum,
your killing me!:wink
- Aug 8, 2007
- 5,256
yes Fred I took the front off with a help of a friend. It could be done for the most part by one person but to take the hood off its better to have two people, its relatively easy when you have a shadowman:lol guiding you
Mullet
FORD GT OWNER
you would be a REAL redneck if you had a paint booth in your bathroom (bonus points if it's in a double wide).
- Aug 8, 2007
- 5,256
actually everybody knows Im a redneck.. I mean who else is got nitrous on their GT?
Mullet
FORD GT OWNER
- Aug 8, 2007
- 5,256