Possible gauge protection solution

Indy GT · Feb 22, 2015

Jay, thanks very much for your thoughts and possible solution to our problem.
I am in as well.

05 Ford GT · Feb 22, 2015

I would be interested in one also..

Pm when ready. I will buy one for sure

Mike

bonehead · Feb 22, 2015

analogdesigner said:
bonehead,

Yes, I forgot to mention this and you are correct that the fuse block IS located in the passenger foot well.

I wish that I could get my hands on a few of these blown gauges so that I can examine the internal circuit board.

Jay

Thanks, Jay. Sign me up for one if you start producing.

texas mongrel · Feb 22, 2015

Fascinating stuff, if your theory is correct, then indeed your design would fix things? Last time I got this involved in gauges was when my POS 246GTS's gauges all crapped out. I couldn't afford a new set so took them all to pieces and soldered in new diodes that I 'd bought at Radio Shack. Total cost a few $$ versus thousands for ferrari OE.

2112 · Feb 23, 2015

I tap would like to get in line if production is realized. :cheers

GTJack · Feb 23, 2015

I am interested as well if you make a "production run."

THamonGT · Feb 23, 2015

I would be interested in purchasing and trying it out also.

standj · Feb 23, 2015

I would love to try one.
John

HPGT · Feb 23, 2015

Count me in -
Thanks

analogdesigner · Feb 23, 2015

cobra,

Exactly, I couldn't of said it any better... Also, a long time ago one of our forum members (Richardhead, I think) was concerned about those air motor coils picking up stray magnetic fields also. Thanks for the info, Jay

cobra498 said:
The microprocessor drives the gauge air motor coils directly with no protection on the leads for emf generated by the coils. I only checked two gauges but the micro was no longer clocking in either defective gauge. Not saying it isn't power supply related, but could be they should have used a buffer circuit for the air motor coils.

junior · Feb 23, 2015

Thanks Jay, a couple of questions please:
What about the effect of your gauge protection system on the new Autometer gauge set (less Speedo and Tach) ?
Any issues with the new combination of gauges (Speedo/Tach remaining OEM with an air core motor and rest of the new gauges have a stepper motor ?
(new gauges- less Speedo and Tach- to be released this February).

TO AWSUM · Feb 23, 2015

Jay, I'd like one when you decide to make a few. Thanks.

Mike Mosing · Feb 23, 2015

Two sets for me.

Cobrar · Feb 23, 2015

Jay - thanks for continued discussion and possible 'next steps' in a solution.

Interested in participating, if you decide to go forward.

Vince H · Feb 23, 2015

I think the 10-20 you were deciding to make up might be spoken for but if there is one left I would love to have it. Thank you for continuing to try and come up with a workable solution to saving our existing gauges.

Vince H

33Bravo · Feb 23, 2015

I also had considered supplying this circuit with the output of a DC-DC converter. Your solution seems more elegant and robust.

fjpikul · Feb 23, 2015

Dear Dr. Frankenstein, please put me on the list for one. YOur next task is to reanimate old, burned out gauges. My tach and speedo are both shot and I would furnish if I had a replacement. Perhaps someone here can furnish Jay some bad gauges? I sent my previous bad ones to Ford. I also might add, there was a question of corrosion in the gauges as well. Nothing was ever confirmed.

Let me call GtGuys.

06fordgt · Feb 23, 2015

I can use at least 1 but 2 if you are so inclined.
Thx

AJK · Feb 23, 2015

I would also be interested in one.

AJK

mmlcobra · Feb 23, 2015

Please put me down for one if you decide to do a run.
Thanks.
Best,
Mark

Possible gauge protection solution

Yea, I got one...too

GT Owner

GT Owner

GT Owner

Blue/white 06'

GT Owner

GT

GT OWNER

GT Owner

GT Owner

GT Owner

Ford GT Owner

GT Owner

GT Owner

GT Owner

GT Owner

GT Owner

GT

GT Owner

GT Owner